原料空隙率对6H-SiC晶体生长初期的影响

doi:10.3724/SP.J.1077.2010.00177

摘要/Abstract

摘要：

生长准备中不同的装料方式导致原料的空隙率不同. 在其它生长工艺参数保持一致的前提下研究了不同空隙率的原料（50%、55%、60%）对SiC晶体生长初期生长速率和结晶质量的影响. 实验发现，在晶体生长初期生长速率随原料空隙率的增大而升高, 过快的结晶速率导致晶体的结晶质量下降. 同时利用有限元方法模拟了不同空隙率的原料（50%、55%、60%）在生长初期内部温度场分布、质量输运以及晶体生长速度. 因为在生长温度下原料内的热量传输主要依靠SiC颗粒间的热辐射, 所以空隙率增大会导致其等效热导率增大. 模拟结果表明：60%空隙率的原料最短时间内达到稳态传热, 初期晶体生长速率最大. 模拟的结果合理地解释了原料空隙率对SiC晶体生长初期的影响规律.

关键词: 碳化硅, 生长速率, 有限元

Abstract:

The source materials with different porosity were be prepared by different loading ways. Effects of the porosity (porosity: 50%,55%,60%) of the source materials on the crystal growth rate and the crystal quality in the initial stage of SiC crystal growth were investigated respectively. It is found that crystal growth rate rises and the crystal quality declines with the increase of the porosity of the source materials. The temperature distribution and mass transport in the source materials (porosity: 50%, 55%, 60%) as well as the growth rate in the initial growth stage are simulated by the finite element method. The heat transfer inside the source material under the typical growth temperature bases on thermal radiation between SiC granulas. The simulations indicate that it takes the least time to reach stationary heat transfer for the source materials with 60% porosity and its growth rate in the initial growth stage is the largest among them. Therefore, the simulations explain the results of the growth experiments very well.

Key words: silicon carbide, growth rate, finite element method

中图分类号:

TB321

刘熙,陈博源,陈之战,宋力昕,施尔畏. 原料空隙率对6H-SiC晶体生长初期的影响[J]. 无机材料学报, DOI: 10.3724/SP.J.1077.2010.00177.

LIU Xi,CHEN Bo-Yuan,CHEN Zhi-Zhan,SONG Li-Xin,SHI Er-Wei. Effects of the Porosity of the Source Materials on the Initial Growth of 6H-SiC Crystal
[J]. Journal of Inorganic Materials, DOI: 10.3724/SP.J.1077.2010.00177.

参考文献

［1］Selder M, Kadinski L, Makarov Yu, et al. Global numerical simulation of heat and mass transfer for SiC bulk crystal growth by PVT. J. Cryst. Growth, 2000, 211(1-4): 333-338.

［2］Klein O, Philip P, Sprekels J, et al. Radiation- and convection-driven transient heat transfer during sublimation growth of silicon carbide single crystals. J. Cryst. Growth, 2001, 222(4): 832-851.

［3］Chen Q S, Zhang H, Prasad V. Heat transfer and kinetics of bulk growth of silicon carbide.J. Cryst. Growth, 2001, 230(1/2): 239-246.

［4］Nishizawa S, Michikawa Y, Kato T, et al. Stress analysis of SiC bulk single crystal growth by sublimation method. Mater. Sci. Forum, 2003, 433-436: 13-16.

［5］Liu X, Shi E W, Song L X, et al. Effects of graphitization of the crucible on silicon carbide crystal growth.J. Cryst. Growth, 2008, 310(19): 4314-4318.

［6］Heydemann V D, Rohrer G S, Sanchez E K, et al. The structural evolution of seed surfaces during the initial stages of physical vapor transport SiC growth. Mater. Sci. Forum, 1998, 264-268: 37-40.

［7］Mantzari A, Polychroniadis E K, Wollweberb J, et al. Defect status near the SiC/substrate interface: investigation of the first stage of the growth by physical vapour transport. J. Cryst. Growth, 2005, 275(1/2): e1813-e1819.

［8］Kitanin E L, Ramm M S, Ris V V, et al. Heat transfer through source powder in sublimation growth of SiC crystal. Mat. Sci. Eng. B,1998, 55(3): 174-183.

［9］Kulik A V, Bogdanov M V, Karpov S Y, et al. Theoretical analysis of the mass transport in the powder charge in long-term bulk SiC growth. Mater. Sci. Forum, 2004, 457-460: 67-70.

［10］Wellmann P J, Herro Z, Winnacket A, et al. In situ visualization of SiC physical vapor transport crystal growth. J. Cryst. Growth, 2005, 275(1/2): e1807-e1812.

［11］Wellmann P J, Herro Z, Sakwe S A, et al. Analysis of graphitization during physical vapor transport growth of silicon carbide. Mater. Sci. Forum, 2004, 457-460: 55-58.

［12］Wellmann P J, Bickermann M, Hofmann D, et al. On the origin of the below band-gap absorption bands in n-Type (N) 4H- and 6H-SiC. Mater. Sci. Forum, 2000, 338-342: 71-74.

[1]	王浩, 刘学超, 郑重, 潘秀红, 徐锦涛, 朱新锋, 陈锟, 邓伟杰, 汤美波, 郭辉, 高攀. 非本征背照触发平面型4H-SiC光导开关性能研究[J]. 无机材料学报, 2024, 39(9): 1070-1076.
[2]	王康龙, 殷杰, 陈晓, 王力, 刘学建, 黄政仁. 颗粒级配对选区激光烧结打印结合常压固相烧结制备碳化硅陶瓷性能的影响[J]. 无机材料学报, 2024, 39(7): 754-760.
[3]	孙川, 何鹏飞, 胡振峰, 王荣, 邢悦, 张志彬, 李竞龙, 万春磊, 梁秀兵. 含有石墨烯阵列的SiC基陶瓷材料的制备与力学性能[J]. 无机材料学报, 2024, 39(3): 267-273.
[4]	徐昊, 钱伟, 花银群, 叶云霞, 戴峰泽, 蔡杰. 皮秒激光加工的微织构对碳化硅润湿性的影响[J]. 无机材料学报, 2023, 38(8): 923-930.
[5]	陈强, 白书欣, 叶益聪. 热管理用高导热碳化硅陶瓷基复合材料研究进展[J]. 无机材料学报, 2023, 38(6): 634-646.
[6]	李一村, 刘雪冬, 郝晓斌, 代兵, 吕继磊, 朱嘉琦. 等离子体聚集装置下的高能量密度单晶金刚石快速生长研究[J]. 无机材料学报, 2023, 38(3): 303-309.
[7]	陈雷, 胡海龙. 柔性PDMS基介电复合材料的电场及击穿损伤形貌演变规律研究[J]. 无机材料学报, 2023, 38(2): 155-162.
[8]	顾薛苏, 殷杰, 王康龙, 崔崇, 梅辉, 陈忠明, 刘学建, 黄政仁. 颗粒级配对黏结剂喷射打印碳化硅陶瓷性能的影响[J]. 无机材料学报, 2023, 38(12): 1373-1378.
[9]	吴松泽, 周洋, 李润丰, 刘晓倩, 李翠伟, 黄振莺. 铁尾矿及其反应烧结多孔陶瓷的制备与性能研究[J]. 无机材料学报, 2023, 38(10): 1193-1199.
[10]	欧阳琴, 王艳菲, 徐剑, 李寅生, 裴学良, 莫高明, 李勉, 李朋, 周小兵, 葛芳芳, 张崇宏, 何流, 杨磊, 黄政仁, 柴之芳, 詹文龙, 黄庆. 核用碳化硅纤维增强碳化硅复合材料研究进展[J]. 无机材料学报, 2022, 37(8): 821-840.
[11]	阮景, 杨金山, 闫静怡, 游潇, 王萌萌, 胡建宝, 张翔宇, 丁玉生, 董绍明. 三维碳化硅纳米线增强碳化硅陶瓷基复合材料的电磁屏蔽性能[J]. 无机材料学报, 2022, 37(5): 579-584.
[12]	阮景, 杨金山, 闫静怡, 游潇, 王萌萌, 胡建宝, 张翔宇, 丁玉生, 董绍明. 碳化硅纳米线增强多孔碳化硅陶瓷基复合材料的制备[J]. 无机材料学报, 2022, 37(4): 459-466.
[13]	李陇彬, 薛玉冬, 胡建宝, 杨金山, 张翔宇, 董绍明. 碳化硅纳米线增韧碳化硅纤维/碳化硅基体损伤行为研究[J]. 无机材料学报, 2021, 36(10): 1111-1117.
[14]	邵笑,刘睿恒,王亮,初靖,白光辉,柏胜强,顾明,张丽娜,马伟,陈立东. 服役条件下方钴矿基热电元件的界面应力分析[J]. 无机材料学报, 2020, 35(2): 224-230.
[15]	罗清,苑青,蒋前勤,于乃森. Cu-SSZ-13/碳化硅废料复合材料的合成及其 NH₃-SCR性能研究[J]. 无机材料学报, 2019, 34(9): 953-960.