生物陶瓷骨骼模型的制作

doi:10.3724/SP.J.1077.2012.00348

无机材料学报 ›› 2012, Vol. 27 ›› Issue (4): 348-352.DOI: 10.3724/SP.J.1077.2012.00348 CSTR: 32189.14.SP.J.1077.2012.00348

生物陶瓷骨骼模型的制作

刘福兴¹, 陈思翰²

(龙华科技大学 1. 机械工程系; 2. 工程技术研究所, 台湾桃园33306)

收稿日期:2011-04-11 修回日期:2011-07-19 出版日期:2012-04-10 网络出版日期:2012-03-12
基金资助:
中国台湾科学委员会(NSC-99-2221-E-262-003) Taiwan Science Council of China (NSC-99-2221-E-262-003)

Fabrication of Bio-ceramic Bone Model

LIU Fwu-Hsing¹, CHEN Ssu-Han²

(1. Department of Mechanical Engineering, Lunghwa University of Science and Technology, Taoyuan 33306, Taiwan, China; 2. Graduate School of Engineering Technology, Lunghwa University of Science and Technology, Taoyuan 33306, Taiwan, China)

Received:2011-04-11 Revised:2011-07-19 Published:2012-04-10 Online:2012-03-12

摘要/Abstract

摘要：

目前商用快速成型机的制备工艺参数与原料都受到限制, 不易制作骨骼模型, 为克服上述缺点, 使用自行开发的快速成型机制作骨骼模型. 本研究主要是以羟基磷灰石、二氧化硅溶胶和少许分散剂混合之浆料为原料, 经由适当的调整加工参数后, 可成型生物陶瓷生胚. 生胚试片分别在1200℃、1300℃、1400℃烧结, 并对其体积收缩率、表面粗糙度和抗压强度进行分析. 经由培养MG63类骨母细胞, 研究骨骼模型表面的细胞活性. 结果显示, 生胚在1200℃烧结时性能较佳, 抗压强度明显上升, 表面粗糙度R_a为12.04 μm, 较适合MG63类骨母細胞生长.

关键词: 生物陶瓷, 骨骼模型, 快速成形, 激光

Abstract:

The process parameters and raw materials of current commercial rapid prototyping (RP) machines are limited, thus the bone model is not easily to fabricate. In order to overcome these disadvantages, a self-developed rapid prototyping machine was used to produce bone model. In this work, the hydroxyapatite (HA), silica sol and suspending agent were mixed as raw materials. By adjusting the suitable process parameter, the bio-ceramic green parts could be formed, and then the specimen green parts were sintered at 1200℃, 1300℃, 1400℃, respectively. The shrinkage, surface roughness and compression strength were tested. Furthermore, the cell activities of the bone model were investigated through the osteoblast MG63 cells culture. The results showed that the green part sintered at 1200℃ exhibits optimum properties with greatly improved compression strength and surface roughness of R_a (12.04 μm), which is suitable for the growth of the osteoblast MG63.

Key words: bio-ceramic, bone model, rapid prototyping, laser

中图分类号:

TQ174

刘福兴, 陈思翰. 生物陶瓷骨骼模型的制作[J]. 无机材料学报, 2012, 27(4): 348-352.

LIU Fwu-Hsing, CHEN Ssu-Han. Fabrication of Bio-ceramic Bone Model[J]. Journal of Inorganic Materials, 2012, 27(4): 348-352.

图/表 7

图1 选择性激光固化法快速成型机

Fig. 1 A rapid prototyping machine of selective laser curing

图2 实验流程示意图

Fig. 2 Schematic of the experimental processes

图3 可成型区域图

Fig. 3 Forming range of the selective laser curing

图4 股骨骨骼模型成品图

Fig. 4 A finished part of femur bone model

图5 股骨骨骼模型表面微观结构SEM照片

Fig. 5 SEM surface image of femur bone model

图6 试片烧结温度与体积收缩率(a), 表面粗糙度(b)和抗压强度(c)的关系

Fig. 6 Effect of sintering temperatures on the shrinkage (a), surface roughness (b) and compression strength (c) of specimen

图7 类骨母细胞在不同培养时间下细胞光密度值

Fig. 7 Optical density of osteoblasts cells cultured for different times

参考文献 14

[1]	Eshraghi S, Das S. Mechanical and microstructure properties of polycaprolactone scaffolds with one-dimensional, two-dimensional, and three-dimensional orthogonally oriented porous architectures produced by selective laser sintering. Acta Biomaterialia., 2010 (6): 2467-2479.
[2]	李武松. 颅颜整形手术用植入物之设计与制作. 桃园: 国立中央大学硕士论文, 1990.
[3]	Peng R S, Wang J B, Yao Q Z. Application study of rapid prototyping manufacturing in media. Chinese Journal of Lasers, 2005, 29(3): 87-88.
[4]	CUI Zhi-Zhong, LI Di-Chen, QIAO Guan-Jun, et al. Peparation of porous carbon template with controllable channels by phenolic resin pyrolyzing. Journal of Inorganic Materials, 2006, 21(4): 848-854.
[5]	Liu F H, Liao Y S. Fabrication of inner complex ceramic parts by selective laser gelling. Journal of the European Ceramic Society. , 2010(30): 3283-3289.
[6]	Liu F H. Manufacturing porous multi-channel ceramics by laser gelling. Ceramics International, 2011(37): 2789-2794.
[7]	赵震锦, 张翀, 张扬, 等. 表面粗糙度对种植体钛片表面成骨细胞的影响. 解剖科学进展, 2008, 14(2): 178-182.
[8]	Goergiou G, Knowles J C. Glass reinforced hydroxyapatite for hard tissue surgery. Biomaterials, 2001(22): 2811-2815.
[9]	Ruys A J, Wei M, Sorrell C C, et al. Sintering effect on the strength of hydroxyapatite. Biomaterials, 1995, 16(5): 409-415.
[10]	ZHANG Lei-Lei, LI He-Jun, LI Ke-Zhi, et al. Effect of surface roughness of carbon/carbon composites on osteoblasts. Journal of Inorganic Materials, 2008, 23(2): 341-345.
[11]	Ponsonnet L, Comte V, Othmane A, et al. Effect of surface topography and chemistry on adhesion, orientation and growth of fibroblasts on nickel-titanium substrates. Materials Science and Engineering C. , 2002, 21(1/2): 157-165.
[12]	Montanaro L, Arciola C R, Campoccia D, et al. In vitro effects on MG63 osteoblast-like cells following contact with two roughness- differing fluorohydroxyapatite-coated titanium alloys. Biomaterials, 2002(23): 3651-3659.
[13]	范震, 贾爽, 苏剑生, 等. 种植体表面粗糙度对成骨细胞增殖及ALP含量的影响. 口腔颌面外科杂志, 2009, 19(2): 128-131.
[14]	Rosa A L, Beloti M M. Rat bone marrow cell response to titanium and titanium alloy with different surface roughness. Clin Oral Implants Res., 2002(14): 43-48.

[1]	刘雷敏, 罗红心, 何玉梅, 金利民, 李永杰, 刘静雯, 魏玉全, 孙安乐, 陈忠明, 刘学建, 殷杰, 黄政仁. 先进光源装置用碳化硅反射镜性能研究[J]. 无机材料学报, 2026, 41(6): 805-813.
[2]	钱新宇, 王无敌, 郭俊尧, 任永春, 董建树, 王庆国, 唐慧丽, 张晨波, 徐晓东, 董永军, 华伟, 徐军. Ho:BaF₂晶体在近红外-中红外波段光谱性能分析[J]. 无机材料学报, 2026, 41(5): 595-603.
[3]	袁子豪, 许银生, 李昕阔, 谭德志. 飞秒激光调控CdS量子点玻璃的发光性能[J]. 无机材料学报, 2026, 41(1): 105-112.
[4]	韩伟伟, 黄东, 李廷松, 李江. 包边复合结构Sm:LuAG/Nd:LuAG激光陶瓷的制备及性能研究[J]. 无机材料学报, 2026, 41(1): 113-118.
[5]	余升阳, 苏海军, 姜浩, 余明辉, 姚佳彤, 杨培鑫. 激光增材制造超高温氧化物陶瓷孔隙缺陷形成及抑制研究进展[J]. 无机材料学报, 2025, 40(9): 944-956.
[6]	马景阁, 吴成铁. 无机生物材料用于毛囊和毛发再生的研究[J]. 无机材料学报, 2025, 40(8): 901-910.
[7]	张洪健, 赵梓壹, 吴成铁. 无机生物材料调控神经细胞功能及神经化组织再生的研究进展[J]. 无机材料学报, 2025, 40(8): 849-859.
[8]	王宇彤, 常江, 徐合, 吴成铁. 硅酸盐生物陶瓷/玻璃促创面修复的研究进展:作用、机制和应用方式[J]. 无机材料学报, 2025, 40(8): 911-920.
[9]	赵凯旋, 刘文鹏, 丁守军, 窦仁勤, 罗建乔, 高进云, 孙贵花, 任浩, 张庆礼. 熔融法制备Nd:YLF原料及其晶体生长和性能研究[J]. 无机材料学报, 2025, 40(5): 529-535.
[10]	陈曦, 袁媛, 谭业强, 刘昌胜. 无机非金属生物材料发展战略研究[J]. 无机材料学报, 2025, 40(5): 449-456.
[11]	殷杰, 耿佳毅, 王康龙, 陈忠明, 刘学建, 黄政仁. SiC陶瓷的3D打印成形与致密化新进展[J]. 无机材料学报, 2025, 40(3): 245-255.
[12]	陈乾, 苏海军, 姜浩, 申仲琳, 余明辉, 张卓. 超高温氧化物陶瓷激光增材制造及组织性能调控研究进展[J]. 无机材料学报, 2024, 39(7): 741-753.
[13]	王康龙, 殷杰, 陈晓, 王力, 刘学建, 黄政仁. 颗粒级配对选区激光烧结打印结合常压固相烧结制备碳化硅陶瓷性能的影响[J]. 无机材料学报, 2024, 39(7): 754-760.
[14]	陈梦杰, 王倩倩, 吴成铁, 黄健. 基于DFT的描述符预测生物陶瓷的降解性[J]. 无机材料学报, 2024, 39(10): 1175-1181.
[15]	郑嘉乾, 卢霄, 鲁亚杰, 王迎军, 王臻, 卢建熙. 医用生物陶瓷的功能性生物适配机制及应用[J]. 无机材料学报, 2024, 39(1): 1-16.

生物陶瓷骨骼模型的制作

Fabrication of Bio-ceramic Bone Model

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

图/表 7

参考文献 14

相关文章 15

编辑推荐

Metrics

本文评价