无压浸渗法制备氧化态SiC颗粒增强铝基复合材料

doi:10.3724/SP.J.1077.2012.00353

无机材料学报 ›› 2012, Vol. 27 ›› Issue (4): 353-357.DOI: 10.3724/SP.J.1077.2012.00353 CSTR: 32189.14.SP.J.1077.2012.00353

无压浸渗法制备氧化态SiC颗粒增强铝基复合材料

张强, 姜龙涛, 武高辉

(哈尔滨工业大学材料科学与工程学院, 哈尔滨150001)

收稿日期:2011-04-16 修回日期:2011-05-30 出版日期:2012-04-10 网络出版日期:2012-03-12
基金资助:
教育部留学回国人员科研启动基金

Fabrication of Oxidized SiC Particles Reinforced Aluminum Matrix Composite by Pressureless Infiltration Technique

ZHANG Qiang, JIANG Long-Tao, WU Gao-Hui

(School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China)

Received:2011-04-16 Revised:2011-05-30 Published:2012-04-10 Online:2012-03-12
Supported by:
Scientific Research Foundation for the Returned Overseas Chinese Scholars, State Education Ministry

摘要/Abstract

摘要：

研究了SiC颗粒在1000~1200℃的氧化行为, 其氧化增重率与保温时间符合抛物线规律, 氧化增重受扩散过程控制, 氧化激活能为219 kJ/mol. 采用预氧化处理的SiC颗粒为增强体, 含Si、Mg的铝合金为基体, 通过无压浸渗方法制备了SiC_p/Al复合材料, 分析了复合材料的微观组织与界面形貌, 探讨了无压浸渗机理. 复合材料中颗粒分布均匀, 无偏聚现象. 材料制备过程中存在界面反应, SiC颗粒表面的氧化层与铝合金中的Mg、Al反应形成了一定数量的MgAl₂O₄. 界面反应的存在提高了润湿性, 促进了无压自发浸渗.

关键词: SiC颗粒, 氧化, 无压浸渗, 界面反应

Abstract:

The oxidation behavior of SiC particles in the temperature range from 1000℃ to 1200℃ was investigated. The dependence of weight gain and oxidation time was parabolic and the oxidation behavior was controlled by diffusion process, with a oxidation activation energy of 219 kJ/mol. Using oxidized SiC particles as reinforcement and aluminum alloy containing Si and Mg as matrix, a SiC_p/Al composite was fabricated by pressureless infiltration technique. The microstructure and interfacial morphology were analyzed and the pressureless infiltration mechanisms were discussed. The particles were distributed uniformly in the composite, without particles agglomeration. Interfacial reactions were found in the composite and the product was identified as MgAl₂O₄, formed by the reactions between surface oxide layer of SiC particles and Mg, Al in the matrix. The interfacial reactions enhanced the wettability and promoted the spontaneous infiltration process.

Key words: SiC particles, oxidation, pressureless infiltration, interfacial reaction

中图分类号:

TB331

张强, 姜龙涛, 武高辉. 无压浸渗法制备氧化态SiC颗粒增强铝基复合材料[J]. 无机材料学报, 2012, 27(4): 353-357.

ZHANG Qiang, JIANG Long-Tao, WU Gao-Hui. Fabrication of Oxidized SiC Particles Reinforced Aluminum Matrix Composite by Pressureless Infiltration Technique[J]. Journal of Inorganic Materials, 2012, 27(4): 353-357.

图/表 6

图1 不同氧化温度下 SiC颗粒的增重率与氧化时间的关系

Fig. 1 Variation in weight gain of SiC particles with oxidation time at different oxidation temperatures

图2 lnK与1/T的关系曲线

Fig. 2 Relationship between lnK and 1/T

图3 SiCp/Al复合材料的背散射组织

Fig. 3 Backscattering image of SiCp/Al composite

图4 铸造态SiCp/Al复合材料的TEM照片

Fig. 4 TEM images of as-cast SiCp/Al composite

图5 SiCp/Al复合材料中提取颗粒的XRD图谱

Fig.5 XRD pattern for the particles extracted from SiCp/Al composite

图6 预氧化SiC与复合材料中提取颗粒的SEM照片及EDS能谱

Fig. 6 SEM morphologies of pre-oxidized SiC and particles extracted from composite

参考文献 13

[1]	Rawal P. Metal-matrix composites for space applications. Journd of the Minerals, Metals and Materials Society, 2001, 53(4): 14-17.
[2]	Fox R T, Newman R A, Pyzik A J, et al. Al2O3-B4C-Al composite material systems via pressureless infiltration methods. Int. J. Appl. Ceram. Technol. , 2010, 7(6): 837-845.
[3]	GU Xiao-Feng, ZHANG Lian-Meng, YANG Mei-Jun, et al. Fabrication and thermophysical properties of SiCp/Al metal-matrix composites by SPS. Journal of Inorganic Materials, 2006, 21(6): 1405-1410.
[4]	Aghajanian M K, Rocazella M A, Burke J T, et al. The fabrication of metal matrix composites by a pressureless infiltration technique. J. Mater. Sci. , 1991, 26(2): 447-454.
[5]	Patro D, Jayaram V. Kinetics of pressureless infiltration of Al-Mg melts into porous alumina preforms. Metall. Mater. Trans. B, 2008, 39(1): 108-115.
[6]	李跃进, 杨银堂, 柴常春, 等. 6H-SiC材料的氧化特性. 西安电子科技大学学报(自然科学版), 2000, 27(4): 460-462.
[7]	Schneider B, Guette A, Naslain R, et al. A theoretical and experimental approach to the active-to-passive transition in the oxidation of silicon carbide - experiments at high temperatures and low total pressures. J. Mater. Sci. , 1998, 33(2): 535-547.
[8]	潘牧, 南策文. 碳化硅(SiC)基材料的高温氧化和腐蚀. 腐蚀科学与防护技术, 2000, 12(2): 109-113.
[9]	丁文江, 翟春泉. 陶瓷粒子在铝合金熔体中的分散行为研究. 热加工工艺, 1992(4): 26-28.
[10]	Pech-Canul M I, Katz R N, Makhlouf M M. Optimum conditions for pressureless infiltration of SiCp preforms by aluminum alloys. J. Mater. Process. Technol. , 2000, 108(1): 68-77.
[11]	Lee K B, Kim Y S, Kwon H. Fabrication of Al-3 wt pct Mg matrix composites reinforced with Al2O3 and SiC particulates by the pressureless infiltration technique. Metall. Mater. Trans. B, 1998, 29(12): 3087-3095.
[12]	Suresh Subra. Mortensen Andreas, Needleman Alan. Fundamentals of Metal-matrix Composites. Butterworth-Heinemann, 1993: 48.
[13]	Garcia-Cordovilla C, Louis E, Pamies A. Surface tension of liquid pure aluminum and aluminum-magnesium alloy. J. Mater. Sci. , 1986, 21(8): 2787-2792.

[1]	杨鑫, 韩春秋, 曹玥晗, 贺桢, 周莹. 金属氧化物电催化硝酸盐还原合成氨研究进展[J]. 无机材料学报, 2024, 39(9): 979-991.
[2]	全文心, 余艺平, 方冰, 李伟, 王松. 管状C/SiC复合材料高温空气氧化行为与宏细观建模研究[J]. 无机材料学报, 2024, 39(8): 920-928.
[3]	潘建隆, 马官军, 宋乐美, 郇宇, 魏涛. 燃料还原法原位制备高稳定性/催化活性SOFC钴基钙钛矿阳极[J]. 无机材料学报, 2024, 39(8): 911-919.
[4]	谭敏, 陈小武, 杨金山, 张翔宇, 阚艳梅, 周海军, 薛玉冬, 董绍明. 流延成型结合反应熔渗制备ZrB₂-SiC陶瓷及其微观结构与氧化行为研究[J]. 无机材料学报, 2024, 39(8): 955-964.
[5]	陈乾, 苏海军, 姜浩, 申仲琳, 余明辉, 张卓. 超高温氧化物陶瓷激光增材制造及组织性能调控研究进展[J]. 无机材料学报, 2024, 39(7): 741-753.
[6]	武向权, 滕家琛, 季祥旭, 郝禹博, 张忠明, 徐春杰. 织构化多孔Al₂O₃-SiO₂复合陶瓷片-球混合浆料特性及光强分布仿真[J]. 无机材料学报, 2024, 39(7): 769-778.
[7]	姜灵毅, 庞生洋, 杨超, 张悦, 胡成龙, 汤素芳. C/SiC-BN复合材料的制备及氧化行为[J]. 无机材料学报, 2024, 39(7): 779-786.
[8]	肖梓晨, 何世豪, 邱诚远, 邓攀, 张威, 戴维德仁, 缑炎卓, 李金华, 尤俊, 王贤保, 林俍佑. 钙钛矿太阳能电池纳米纤维改性电子传输层研究[J]. 无机材料学报, 2024, 39(7): 828-834.
[9]	叶梓滨, 邹高昌, 吴琪雯, 颜晓敏, 周明扬, 刘江. 阳极支撑型锥管串接式直接碳固体氧化物燃料电池组的制备及性能[J]. 无机材料学报, 2024, 39(7): 819-827.
[10]	曹青青, 陈翔宇, 吴健豪, 王筱卓, 王乙炫, 王禹涵, 李春颜, 茹菲, 李兰, 陈智. SiO₂增强自敏性氮化碳微球可见光降解盐酸四环素的研究[J]. 无机材料学报, 2024, 39(7): 787-792.
[11]	王伟明, 王为得, 粟毅, 马青松, 姚冬旭, 曾宇平. 以非氧化物为烧结助剂制备高导热氮化硅陶瓷的研究进展[J]. 无机材料学报, 2024, 39(6): 634-646.
[12]	蔡飞燕, 倪德伟, 董绍明. 高熵碳化物超高温陶瓷的研究进展[J]. 无机材料学报, 2024, 39(6): 591-608.
[13]	刘国昂, 王海龙, 方成, 黄飞龙, 杨欢. B₄C含量对(Ti_0.25Zr_0.25Hf_0.25Ta_0.25)B₂-B₄C陶瓷力学性能及抗氧化性能的影响[J]. 无机材料学报, 2024, 39(6): 697-706.
[14]	郑斌, 康凯, 张青, 叶昉, 解静, 贾研, 孙国栋, 成来飞. 前驱体转化陶瓷法制备Ti₃SiC₂陶瓷及其热稳定性研究[J]. 无机材料学报, 2024, 39(6): 733-740.
[15]	张幸红, 王义铭, 程源, 董顺, 胡平. 超高温陶瓷复合材料研究进展[J]. 无机材料学报, 2024, 39(6): 571-590.

无压浸渗法制备氧化态SiC颗粒增强铝基复合材料

Fabrication of Oxidized SiC Particles Reinforced Aluminum Matrix Composite by Pressureless Infiltration Technique

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

图/表 6

参考文献 13

相关文章 15

编辑推荐

Metrics

本文评价