电纺FeMnO3纳米纤维毛毡的制备及电化学性能研究

doi:10.15541/jim20180409

无机材料学报 ›› 2019, Vol. 34 ›› Issue (7): 709-714.DOI: 10.15541/jim20180409 CSTR: 32189.14.10.15541/jim20180409

电纺FeMnO₃纳米纤维毛毡的制备及电化学性能研究

孙晓璐¹,宋肖飞¹,刘艳华¹,吴越¹,蔡以兵^1,²(),赵宏梅²

^1. 江南大学生态纺织教育部重点实验室, 无锡 214122
^2. 仪征盛大纺织新材料有限公司, 仪征 225002

收稿日期:2018-09-06 修回日期:2018-11-25 出版日期:2019-07-20 网络出版日期:2019-06-26
作者简介:孙晓璐(1995-), 女, 硕士研究生. E-mail:xiaoluS0611@163.com
基金资助:
中央高校基本科研业务费专项资金(JUSRP51621A);江苏高校"青蓝工程"优秀青年骨干教师培养对象资助项目苏教师(【2016】15号);江苏省"双创计划"科技副总项目(FZ20180843);江南大学大学生创新训练计划项目(2018224Y)

Electrospun FeMnO₃ Nanofibrous Mats: Preparation and Electrochemical Property

SUN Xiao-Lu¹,SONG Xiao-Fei¹,LIU Yan-Hua¹,WU Yue¹,CAI Yi-Bing^1,²(),ZHAO Hong-Mei²

^1. Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, China
^2. Yizheng Shengda Textile Material Co., Ltd, Yizheng 225002, China

Received:2018-09-06 Revised:2018-11-25 Published:2019-07-20 Online:2019-06-26
Supported by:
Fundamental Research Funds for Central Universities(JUSRP51621A);Vice President of Science and Technology of Jiangsu Province Double Plan(【2016】15号);Jiangsu Universities "Qing Lan"Project(FZ20180843);Undergraduate Innovation and Training Program of Jiangnan University(2018224Y)

摘要/Abstract

摘要：

本研究以聚乙烯吡咯烷酮(PVP)、九水硝酸铁和四水合醋酸锰为原料, 无水乙醇和N,N-二甲基甲酰胺为溶剂, 配置了均一稳定的前驱体纺丝液, 利用静电纺丝技术制备了PVP/Mn(COOH)₂/Fe(NO₃)₃复合纳米纤维, 高温煅烧后得到了锰酸铁(FeMnO₃)纳米纤维毛毡, 用其作为锂电池负极材料。利用红外光谱(FT-IR)、X射线衍射(XRD)、扫描电镜(SEM)和BET比表面积分析仪等研究样品的表观形貌与晶型结构。结果表明: 煅烧后制得的FeMnO₃纳米纤维毛毡具有良好的形貌结构, 比表面积为9.9 m2/g, 当温度达到470 ℃后, 曲线变得平缓, 热重损失不明显。充放电、循环伏安以及循环性能测试结果表明, FeMnO₃纳米纤维毛毡具有良好的电化学性能及电稳定性, 首次充电比容量为1264 mAh/g, 在50 mA/g电流密度下经过37次循环后其比容量仍保持在533 mAh/g; 在循环50次后, 阻抗约为170 Ω, 基本保持不变。

关键词: 静电纺丝, FeMnO₃纳米纤维毛毡, 锂电池, 电化学性能

Abstract:

A uniform and stable precursor spinning solution was prepared by using polyvinylpyrrolidone (PVP), ferric nitrate nonahydrate and manganese acetate tetrahydrate as raw materials, anhydrous ethanol and N,N-dimethylformamide as solvent, followed by magnetically stirred. The PVP/Mn(COOH)₂/Fe(NO₃)₃ composite nanofibers were prepared by electrospinning technology. FeMnO₃ nanofibrous mats were obtained after high temperature calcination, which was used as anode material for lithium battery. Apparent morphology and crystal structure of the samples were investigated by FT-IR, XRD, SEM, and BET specific surface area analyzers. All results showed that the fabricated FeMnO₃ nanofibrous mats possessed good structural morphology with the specific surface area of 9.9 m ²/g. TG analysis showed that when temperature reaches 470 ℃, the TG curve becomes gentle while the mass loss is not obvious. Results form charge and discharge, cyclic voltammetry, and cycle performance tests, indicated that FeMnO₃ nanofibrous mats had good electrochemical performance and electrical stability, with a specific capacity of 533 mAh/g at 50 mA/g after 37 cycles. After 50 cycles, the impedance is approximately 170 Ω, which remains essentially unchanged.

Key words: electrospinning, FeMnO₃ nanofibrous mats, lithium battery, electrochemical performance

中图分类号:

TQ340

孙晓璐,宋肖飞,刘艳华,吴越,蔡以兵,赵宏梅. 电纺FeMnO₃纳米纤维毛毡的制备及电化学性能研究[J]. 无机材料学报, 2019, 34(7): 709-714.

SUN Xiao-Lu,SONG Xiao-Fei,LIU Yan-Hua,WU Yue,CAI Yi-Bing,ZHAO Hong-Mei. Electrospun FeMnO₃ Nanofibrous Mats: Preparation and Electrochemical Property[J]. Journal of Inorganic Materials, 2019, 34(7): 709-714.

图/表 8

图1 PVP/Mn(COOH)2/Fe(NO3)3复合纳米纤维的TG和DTG曲线

Fig. 1 TG and DTG curves of PVP/Mn(COOH)2/Fe(NO3)3 composite nanofibers

图2 样品煅烧前(a)后(b)的红外光谱图

Fig. 2 Infrared spectra of samples before and after calcination (a) PVP/Mn(COOH)2/Fe(NO3)3 composite nanofibers; (b) FeMnO3 nanofibrous mats

图3 FeMnO3纳米纤维毛毡的XRD图谱

Fig. 3 XRD pattern of FeMnO3 nanofibrous mats

图4 (a) PVP/Mn(COOH)2/Fe(NO3)3复合纳米纤维的SEM照片; 煅烧后FeMnO3纳米纤维毛毡SEM(b)和TEM(c)照片

Fig. 4 (a) SEM image of PVP/Mn(COOH)2/Fe(NO3)3 composite nanofibers, and (b) SEM and (c) TEM images of FeMnO3 nanofibrous mats after calcination

图5 FeMnO3纳米纤维毛毡的N2等温吸附-脱附曲线

Fig. 5 N2 adsorption-desorption isotherm of FeMnO3 nanofibrous mats

图6 FeMnO3纳米纤维毛毡的循环伏安曲线

Fig. 6 Cyclic voltammograms of FeMnO3 nanofibrous mats

图7 FeMnO3纳米纤维毛毡的(a)充放电曲线和(b)循环性能曲线

Fig. 7 (a) Charge-discharge and (b) cycle performance curves of FeMnO3 nanofibrous mats

图8 FeMnO3纳米纤维毛毡的交流阻抗图谱

Fig. 8 AC impedance diagram of FeMnO3 nanofibrous mats

参考文献 21

[1]	LUO L . Preparation and Lithium Storage Properties of Ferrite Nanofiber Composite Anode Materials. Wuxi: Doctoral Dissertation of Jiangnan University, 2017.
[2]	LIANG J J, YUAN C C, LI H H , et al. Growth of SnO₂ nanoflowers on N-doped carbon nanofibers as anode for Li- and Na-ion batteries. Nano-Micro Letters, 2018,10(21):1-9. DOI URL
[3]	YANG Q, FENG S Q, LIU J W , et al. Synthesis of porous Co₃O₄/C nanoparticles as anode for Li-ion battery application. Applied Surface Science, 2018,443:401-406. DOI URL
[4]	LUO W . Construction of One-dimensional Nano-transition Metal Oxides Based on Electrospinning Technology and its Lithium Storage performance. Wuhan: Doctoral Dissertation of Huazhong University of Science and Technology, 2012.
[5]	LI JING, ZHAO H X, LIU F S, XU H F , et al. Preparation and electrochemical performance of lithium ion battery ferric manganese anode materials. Nonferrous Metals Engineering, 2016,6(5):5-8.
[6]	YAN W . Preparation and Properties of TiO₂ as Anode Material for Lithium Ion Battery. Changchun: Doctoral Dissertation of Jilin University, 2014.
[7]	GONG G, WANG L, XU A , et al. Preparation and properties of electrospun PMMA/EVOH-SO₃Li lithium ion battery separator composites. Journal of Composite Materials, 2018,35(3):477-484.
[8]	CAI D . Research on Graphene-based High Performance Lithium Ion Battery Anode Material. Guangzhou: Doctoral Dissertation of South China University of Technology, 2014.
[9]	DENG Q . Preparation and Properties of Transition Metal Oxide/ Graphene Composite Anodes for Lithium ion Batteries. Shenzhen: Master Dissertation of Shenzhen University, 2017.
[10]	FAN X . Research on Anode Materials of Metal Oxide/Graphene Lithium Ion Battery. Tianjin: Master Dissertation of Tianjin Polytechnic University, 2017.
[11]	QIN J, LIU D Y, ZHAO N Q , et al. Fabrication of Sn-core/ CNT-shell nanocable anchored interconnected carbon networks as anode material for lithium ion batteries. Materials Letters, 2018,212:94-97. DOI URL
[12]	WANG L, SHI S, SONG H , et al. Preparation and electrochemical performance of ZrO₂/PVDF-PAN supercapacitor separator by electrospinning method. Journal of Composite Materials, 2017,34(8):1660-1666.
[13]	LEE Y I, JANG D H, KIM J W . Electrospun NiFe₂O₄ nanofibers as high capacity anode materials for Li-ion batteries. Journal of Nanoscience and Nanotechnology, 2013,13(10):7138-7141. DOI URL
[14]	LAVELA P, TIRADO J L . CoFe₂O₄ and Ni Fe₂O₄ synthesized by Sol-Gel procedures for their use as anode materials for Li ion batteries. Journal of Power Sources, 2007,172(1):379-387. DOI URL
[15]	POIZOT P, LARUELLE S, GRUGEON S , et al. Nano-sized transition-metal oxides as negative electrode materials for lithium-ion batteries. Nature, 2000,407:488-496.
[16]	ZHANG T, ZHU H B, CROUE J P , et al. Production of sulfate radical from peroxymonosulfate induced by a magnetically separable CuFe₂O₄ spinel in water: efficiency, stability, and mechanism. Environmental Science and Technolgy, 2013,47(6):2784-2791. DOI URL
[17]	MONRÓS G, CARDS J, TENA M A , et al. Spinets from gelatine- protected gels. Journal of Materials Chemistry, 1995,5(1):85-90. DOI URL
[18]	QIAN H S, HU Y, LI Z Q , et al. ZnO/ZnFe₂O₄ magnetic fluorescent bifunctional hollow nanospheres: synthesis, characterization, and their optical/magnetic properties. The Journal of Physical Chemistry C, 2010,114(41):17455-17459. DOI URL
[19]	YANG X H, WANG X, ZHANG Z D , et al. Electrochemical properties of submicron cobalt ferrite spinel through a co-precipitation method. Journal of Crystal Growth, 2005,277(1-4):467-470. DOI URL
[20]	LAVELA P, TIRADO J L, WOMES M , et al. Elucidation of capacity fading on CoFe₂O₄ conversion electrodes for lithium batteries based on Fe-57 mossbauer spectroscopy. Journal of The Electrochemical Society, 2009,156(7):A589-A594. DOI URL
[21]	ZHANG G Q, LOU X W . General solution growth of mesoporous NiCo₂O₄ nanosheets on various conductive substrates as high- performance electrodes for supercapacitors. Advanced Materials, 2013,25(7):976-979. DOI URL

电纺FeMnO₃纳米纤维毛毡的制备及电化学性能研究

Electrospun FeMnO₃ Nanofibrous Mats: Preparation and Electrochemical Property

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

图/表 8

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价

[1]	万俊池, 杜路路, 张永上, 李琳, 刘建德, 张林森. Na₄Fe_xP₄O₁₂₊_x/C钠离子电池正极材料的结构演变及其电化学性能[J]. 无机材料学报, 2025, 40(5): 497-503.
[2]	薛柯, 蔡长焜, 谢满意, 李舒婷, 安胜利. 固体氧化物燃料电池Pr₁₊_xBa_1-_xFe₂O₅₊_δ阴极材料的制备及电化学性能研究[J]. 无机材料学报, 2025, 40(4): 363-371.
[3]	陈正鹏, 金芳军, 李明飞, 董江波, 许仁辞, 徐韩昭, 熊凯, 饶睦敏, 陈创庭, 李晓伟, 凌意瀚. 双钙钛矿Sr₂CoFeO₅₊_δ阴极材料的制备及其中温固体氧化物燃料电池性能研究[J]. 无机材料学报, 2024, 39(3): 337-344.
[4]	谭淑雨, 刘晓宁, 毕志杰, 万勇, 郭向欣. 正极包覆与界面修饰: 双策略改善聚氧化乙烯固态电解质对高电压正极稳定性[J]. 无机材料学报, 2023, 38(12): 1466-1474.
[5]	盛丽丽, 常江. 光/磁热Fe₂SiO₄/Fe₃O₄双相生物陶瓷及其复合电纺丝膜制备及抗菌性能研究[J]. 无机材料学报, 2022, 37(9): 983-990.
[6]	夏求应, 孙硕, 昝峰, 徐璟, 夏晖. 非晶LiSiON薄膜电解质的全固态薄膜锂电池性能[J]. 无机材料学报, 2022, 37(2): 230-236.
[7]	刘城, 赵倩, 牟志伟, 雷洁红, 段涛. 新型铋基SiOCNF复合膜对放射性气态碘的吸附性能[J]. 无机材料学报, 2022, 37(10): 1043-1050.
[8]	张晓山, 王兵, 吴楠, 韩成, 刘海燕, 王应德. 高红外遮蔽SiZrOC纳米纤维膜的制备及其性能研究[J]. 无机材料学报, 2022, 37(1): 93-100.
[9]	王袁杰, 裴学良, 李好义, 徐鑫, 何流, 黄政仁, 黄庆. 自由基引发活性聚碳硅烷交联及其在制备SiC纤维中的应用[J]. 无机材料学报, 2021, 36(9): 967-973.
[10]	马玲玲, 常江. Nd掺杂硅酸钙及其复合电纺丝膜的制备及性能研究[J]. 无机材料学报, 2021, 36(9): 974-980.
[11]	刘芳芳, 传秀云, 杨扬, 李爱军. 氮/硫共掺杂对纤水镁石模板碳纳米管电化学性能的影响[J]. 无机材料学报, 2021, 36(7): 711-717.
[12]	李婷婷, 张志明, 韩正波. 基于静电纺丝技术的聚合物基MOFs纳米纤维膜的研究进展[J]. 无机材料学报, 2021, 36(6): 592-600.
[13]	包峰, 常江. 硅酸钙纳米线复合电纺丝支架的制备及离子释放研究[J]. 无机材料学报, 2021, 36(11): 1199-1207.
[14]	张亚萍,雷宇轩,丁文明,于濂清,朱帅霏. 双铁电复合材料的制备及其光电化学性能研究[J]. 无机材料学报, 2020, 35(9): 987-992.
[15]	朱正旺,冯锐,柳扬,张扬,谢文翰,董丽杰. 类鱼骨结构CoFe₂O₄纳米纤维的制备与性能[J]. 无机材料学报, 2020, 35(9): 1011-1016.