电镀镍-钴合金对La-Mg-Ni基贮氢合金电化学性能的影响

doi:10.3724/SP.J.1077.2010.00647

无机材料学报 ›› 2010, Vol. 25 ›› Issue (6): 647-652.DOI: 10.3724/SP.J.1077.2010.00647 CSTR: 32189.14.SP.J.1077.2010.00647

电镀镍-钴合金对La-Mg-Ni基贮氢合金电化学性能的影响

丁慧玲^1,2, 蒿建生^1,3, 朱惜林^2,3, 李媛², 韩树民^1,2, 张静武¹

(1.燕山大学亚稳材料制备技术与科学国家重点实验室, 秦皇岛 066004; 2.燕山大学环境与化学工程学院, 秦皇岛 066004; 3.内蒙古稀奥科贮氢合金有限公司, 包头 014030)

收稿日期:2009-12-29 修回日期:2010-02-10 出版日期:2010-06-20 网络出版日期:2010-05-12
基金资助:
国家自然科学基金(20673093);河北省自然科学基金(B2007000303)

Electrochemical Performance Studies on Nickel-cobalt Electroplated La-Mg-Ni-based Hydrogen Storage Alloys

DING Hui-Ling^1,2, HAO Jian-Sheng^1,3, ZHU Xi-Lin^2,3, LI Yuan², HAN Shu-Min^1,2, ZHANG Jing-Wu¹

(1. State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China; 2. College of Environmental and Chemical Engineering, Yanshan University, Qinhuangdao 066004, China; 3. Inner Mongolia Rare Earth Ovonic Hydrogen Storage Alloys Corporation Limited, Baotou 014030, China)

Received:2009-12-29 Revised:2010-02-10 Published:2010-06-20 Online:2010-05-12

摘要/Abstract

摘要： 为了改善La-Mg-Ni基贮氢合金的循环稳定性和综合电化学性能, 研究了电镀镍-钴合金对La_0.88Mg_0.12Ni_2.95Mn_0.10Co_0.55Al_0.10贮氢合金粉末表面形貌和电极电化学性能的影响. FESEM表明, 电镀处理后合金粉末表面沉积了球状的镍-钴合金颗粒. 电化学性能测试表明, 贮氢合金电极的放电容量、高倍率放电性能和循环稳定性均得到了显著改善. 200周循环时合金电极的容量保持率从未处理合金电极的60%提高到镀覆镍-钴合金的80%, 在放电电流密度1080mA/g下的高倍率放电性能提高了23%. 线性极化曲线和电化学阻抗分析结果显示, 包覆镍-钴合金后贮氢合金电极表面的电荷转移速率加快, 电催化活性提高.

关键词: La-Mg-Ni基贮氢合金, 表面处理, 电镀, 镍-钴合金, 电化学性能

Abstract: In order to improve cycling stability and overall electrochemical properties of La-Mg-Ni-based hydrogen storage alloys, an electroplating treatment was applied on La_0.88Mg_0.12Ni_2.95Mn_0.10Co_0.55Al_0.10alloy powders. The effect of cobalt-nickel coating on the morphological and electrochemical properties was studied. FESEM results show that spherical nickel-cobalt alloy particles are deposited on the surface of the alloys. Electrochemical tests indicate that the maximum discharge capacity, the cycling stability and the high rate dischargeability (HRD) are remarkably improved. After 200 charge/discharge cycles, the capacity retention rate increases from 60% (uncoated) to 80% (nickel-cobalt coated). The HRD at 1080mA/g rises by 23% for the nickel-cobalt coated alloy electrodes. Linear polarization and Electrochemical Impedance Spectroscope (EIS) results reveal that the surface of alloy electrodes with cobalt-nickel coatings is more catalytic for the electrochemical charge transfer reactions.

Key words: La-Mg-Ni-based hydrogen storage alloy, surface treatment, electroplating, nickel-cobalt alloy, electrochemical characteristics

中图分类号:

TM 912

丁慧玲1,2, 蒿建生1,3, 朱惜林2,3, 李媛2, 韩树民1,2, 张静武1. 电镀镍-钴合金对La-Mg-Ni基贮氢合金电化学性能的影响[J]. 无机材料学报, 2010, 25(6): 647-652.

DING Hui-Ling1,2, HAO Jian-Sheng1,3, ZHU Xi-Lin2,3, LI Yuan2, HAN Shu-Min1,2, ZHANG Jing-Wu1. Electrochemical Performance Studies on Nickel-cobalt Electroplated La-Mg-Ni-based Hydrogen Storage Alloys[J]. Journal of Inorganic Materials, 2010, 25(6): 647-652.

参考文献

[1]Ruiz F C, Castro E B, Real S G, et al. Electrochemical characterization of AB₂ alloys used for negative electrodes in Ni/MH batteries. Int. J. Hydrogen Energy, 2008, 33(13): 3576-3580.

[2]Chen J, Takeshita H T, Tanaka H, et al. Hydriding properties of LaNi₃ and CaNi₃ and their substitutes with PuNi₃-type structure. J. Alloys Compd., 2000, 302(1/2): 304-313.

[3]Gu H, Zhu Y F, Li L Q. Effect of La/Ni ratio on hydrogen storage properties of Mg–Ni–La system prepared by hydriding combustion synthesis followed by mechanical milling. Int. J. Hydrogen Energy, 2008, 33(12): 2970-2974.

[4]Liu Y F, Pan H G, Gao M X, et al. Investigation on the characteristics of La_0.7Mg_0.3Ni_2.65Mn_0.1Co_0.75+x (x = 0.00–0.85) metal hydride electrode alloys for Ni/MH batteries Part II: Electrochemical performances. J. Alloys Compd., 2005, 388(1/2): 109-117.

[5]Zhao X Y, Ma L Q, Gao Y J, et al. Effect of surface treatments on microstructure and electrochemical properties of La–Ni–Al hydrogen storage alloy. Int. J. Hydrogen Energy, 2009, 34(4): 1904-1909.

[6]Ise T, Murata T, Hirota Y, et al. The surface structure and the electrochemical properties of hydrogen-absorbing alloys treated with an HCl aqueous solution. J. Alloys Compd., 2000, 307(1/2): 324-332.

[7]Xiao L L, Wang Y J, Liu Y, et al. Influence of surface treatments on microstructure and electrochemical properties of La_0.7Mg_0.3-Ni_2.4Co_0.6 hydrogen-storage alloy. Int. J. Hydrogen Energy, 2008, 33(14): 3925-3929.

[8]Qiu S J, Chu H L, Zhang Y, et al. The electrochemical performances of Ti–V-based hydrogen storage composite electrodes prepared by ball milling method. Int. J. Hydrogen Energy, 2008, 33(24): 7471-7478.

[9]Wei X, Zhang P, Dong H, et al. Electrochemical performances of a Co-free La(NiMnAlFe)₅hydrogen storage alloy modified by surface coating with Cu. J. Alloys Compd., 2008, 458(1/2): 583-587.

[10]Raju M, Ananth M V, Vijayaraghavan L. Influence of electroless coatings of Cu, Ni–P and Co–P on M_mNi_3.25Al_0.35Mn_0.25Co_0.66 alloy used as anodes in Ni–MH batteries. J. Alloys Compd., 2009, 475(1/2): 664-671.

[11]Ambrosio R C, Ticianelli E A. Studies on the influence of palladium coatings on the electrochemical and structural properties of a metal hydride alloy. Surf. Coat Technol., 2005, 197(2/3): 215-222.

[12]刘素琴, 陈东洋, 黄可龙, 等(LIU Su-Qin, et al). MgNi-TiNi_0.56M_0.44 (M=Al、Fe)贮氢合金的制备和电化学性能研究. 无机材料学报(Journal of Inorganic Materials), 2009, 24(2): 361-366.

[13]Durairajan A, Haran B S, Popov B N, et al. Cycle life and utilization studies on cobalt microencapsulated AB5 type metal hydride. J. Power Sources, 1999, 83(1/2): 114-120.

[14]Wu M S, Wu H R, Wang Y Y, et al. Electrochemical investigation of hydrogen-storage alloy electrode with duplex surface modification. Int. J. Hydrogen Energy, 2004, 29(12): 1263-1269.

[15]Ding H L, Han S M, Liu Y, et al. Electrochemical performance studies on cobalt and nickel electroplated La–Mg–Ni-based hydrogen storage alloys. Int. J. Hydrogen Energy, 2009, 34(23): 9402-9408.

[16]Gomez E, Pan S, Valles E. Electrodeposition of Co–Ni and Co–Ni–Cu systems in sulphate–citrate medium. Electrochim. Acta, 2005, 51(1): 146-153.

[17]Chi B, Li J, Yang X, et al. Deposition of Ni–Co by cyclic voltammetry method and its electrocatalytic properties for oxygen evolution reaction. Int. J. Hydrogen Energy, 2005, 30(1): 29-34.

[18]Miao H J, Piron D L. Composite-coating electrodes for hydrogen evolution reaction. Electrochim. Acta, 1993, 38(8): 1079-1085.

[19]Ma S, Gao M X., Li R, et al. A study on the structural and electrochemical properties of La_0.7-xNd_xMg_0.3Ni_2.45Co_0.75Mn_0.1Al_0.2 (x = 0.0–3.0) hydrogen storage alloys. J. Alloys Compd., 2008, 457(1/2): 457-467.

[20]Liu Y F, Pan H G, Yue Y J, et al. Cycling durability and degradation behavior of La–Mg–Ni–Co-type metal hydride electrodes. J. Alloys Compd., 2005, 395(1/2): 291-299.

[21]Li Y, Han D, Han S M, et al. Effect of rare earth elements on electrochemical properties of La–Mg–Ni-based hydrogen storage alloys. Int. J. Hydrogen Energy, 2009, 34(3): 1399-1404.

[22]Iwakura C, Oura T, Inoue H, et al. Effects of substitution with foreign metals on the crystallographic, thermodynamic and electrochemical properties of AB₅-type hydrogen storage alloys. Electrochim. Acta, 1996, 41(1): 117-121.

[23]Notten P H L, Hokkeling P. Double-phase hydride forming compounds: a new class of highly electrocatalytic materials. J. Electro- chem. Soc., 1991, 138(7): 1877-1885.

[24]Kuriyama N, Sakai T, Miyamura H, et al. Electrochemical impedance and deterioration behavior of metal hydride electrodes. J. Alloys Compd., 1993, 202(1/2): 183-197.

编辑推荐 0

Metrics

阅读次数

全文

2578

HTML			PDF

最新录用	在线预览	正式出版	最新录用	在线预览	正式出版
0	0	1	0	0	2577

来源	本网站	其他网站

次数	550	2028
比例	21%	79%

摘要

3232

最新录用	在线预览	正式出版

0	0	3232

来源	本网站	其他网站

次数	97	3135
比例	3%	97%

电镀镍-钴合金对La-Mg-Ni基贮氢合金电化学性能的影响

Electrochemical Performance Studies on Nickel-cobalt Electroplated La-Mg-Ni-based Hydrogen Storage Alloys

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐 0

Metrics

本文评价

[1]	陈正鹏, 金芳军, 李明飞, 董江波, 许仁辞, 徐韩昭, 熊凯, 饶睦敏, 陈创庭, 李晓伟, 凌意瀚. 双钙钛矿Sr₂CoFeO₅₊_δ阴极材料的制备及其中温固体氧化物燃料电池性能研究[J]. 无机材料学报, 2024, 39(3): 337-344.
[2]	刘芳芳, 传秀云, 杨扬, 李爱军. 氮/硫共掺杂对纤水镁石模板碳纳米管电化学性能的影响[J]. 无机材料学报, 2021, 36(7): 711-717.
[3]	张亚萍,雷宇轩,丁文明,于濂清,朱帅霏. 双铁电复合材料的制备及其光电化学性能研究[J]. 无机材料学报, 2020, 35(9): 987-992.
[4]	湛菁,徐昌藩,龙怡宇,李启厚. 聚丙烯酰胺凝胶法制备Bi₂Mn₄O₁₀及其电化学性能[J]. 无机材料学报, 2020, 35(7): 827-833.
[5]	郑坤, 罗永春, 邓安强, 杨洋, 张海民. A₂B₇型La_0.3Y_0.7Ni_3.4-_xMn_xAl_0.1储氢合金微观结构和电化学性能研究[J]. 无机材料学报, 2020, 35(5): 549-555.
[6]	朱泽阳,魏济时,黄健航,董向阳,张鹏,熊焕明. 晶格空位ZnO纳米棒的制备及其在镍锌电池中的应用[J]. 无机材料学报, 2020, 35(4): 423-430.
[7]	李学林, 朱建锋, 焦宇鸿, 黄家璇, 赵倩楠. 二氧化锰形貌对Ti₃C₂T_x@MnO₂复合材料电化学性能的影响[J]. 无机材料学报, 2020, 35(1): 119-125.
[8]	张亚萍, 丁文明, 朱海丰, 黄承兴, 于濂清, 王永强, 李哲, 徐飞. 电还原MoSe₂修饰TiO₂纳米管光电化学性能研究[J]. 无机材料学报, 2019, 34(8): 797-802.
[9]	孙晓璐,宋肖飞,刘艳华,吴越,蔡以兵,赵宏梅. 电纺FeMnO₃纳米纤维毛毡的制备及电化学性能研究[J]. 无机材料学报, 2019, 34(7): 709-714.
[10]	冯晓晶, 王恭凯, 王晓然, 何珺, 王新, 彭会芬. Cr ³⁺掺杂LiSn₂(PO₄)₃负极材料的电化学性能研究[J]. 无机材料学报, 2019, 34(4): 358-364.
[11]	王家虎, 王文馨, 杜鹏, 胡芳东, 姜晓蕾, 杨剑. Na₃V₂(PO₄)₂F₃@V₂O_5-_x复合材料的制备及储钠性能研究[J]. 无机材料学报, 2019, 34(10): 1097-1102.
[12]	范广新, 刘泽萍, 闻寅, 刘宝忠. 硅烷偶联剂表面处理对LiNi_0.8Co_0.15Al_0.05O₂结构和性能的影响[J]. 无机材料学报, 2018, 33(7): 749-755.
[13]	王浩, 罗永春, 邓安强, 赵磊, 姜婉婷. 退火温度对无镁La-Y-Ni系A₂B₇型合金相结构和电化学性能的影响[J]. 无机材料学报, 2018, 33(4): 434-440.
[14]	罗凌虹, 胡佳幸, 程亮, 徐序, 吴也凡, 林囿辰. Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-_δ-Ce_0.9Gd_0.1O_2-_δ中低温固体氧化物燃料电池复相阴极的研究[J]. 无机材料学报, 2018, 33(4): 441-446.
[15]	张国雄, 陈月梅, 何臻妮, 林川, 陈益钢, 郭海波. 表面活性剂对NiCo₂S₄纳米薄膜的电化学性能影响的研究[J]. 无机材料学报, 2018, 33(3): 289-294.