高级检索
无机材料学报

无机材料学报

• 研究论文 • 上一篇    下一篇

溶胶-凝胶法制备无机复合膜催化材料

盛梅; 朱毅青; 吴泽彪; 林西平; 栗洪道   

  1. 江苏石油化工学院化工系; 江苏常州 213016
  • 收稿日期:1999-01-04 修回日期:1999-02-01 出版日期:1999-12-20 网络出版日期:1999-12-20

Research on the Inorganic Composite Membrane Catalyst by the Sol-gel Process

SHENG Mei; ZHU Yi-Qing; WU Ze-Biao; LIN Xi-Ping; LI Hong-Dao   

  1. Department of Chemical Engineering; Jiangsu Institute of Petrochemical Technology; Changzhou 213016; China
  • Received:1999-01-04 Revised:1999-02-01 Published:1999-12-20 Online:1999-12-20

PDF (PC)

862

被引次数

11

摘要： 以正硅酸乙酯（TEOS）、硝酸铁和银酸铵为原料，用溶胶－凝胶法制备了Fe－Si－O和Mo－O溶胶，通过浸渍－提拉法，分别制得了Fe－Si－O薄膜（以载玻片为基板）和MO－Fe－Si－O薄膜（以多孔α－Al2O3为基质材料）．考察了制备工艺条件对Fe－Si－O成膜的影响，采用DTA、XRD和SEM等技术研究了热处理条件对Mo－Fe－Si－O薄膜结构的影响．结果表明：溶胶粘度、衬底材质、浸渍时间、提拉速度等是影响Fe－Si－O成膜的主要因素；溶胶－凝胶法制备的Mo－Fe－Si－O／α－Al2O3无机复合膜热处理温度达到650℃以上，即能形成比较明显的结晶相，薄膜经高温焙烧（700℃）－冷却反复5次，膜表面没有出现剥离和开裂现象．

关键词: 溶胶－凝胶, Fe－Si－O溶胶, Mo－O溶胶, Mo－Fe－Si－O薄膜

Abstract: Fe-Si-O and Mo-O sols were prepared by sol-gel process by using Si(OC2H5)4 (TEOS), Fe(NO3)3·9H2O and (NH4)6·Mo7O24·4H2O.
The Fe-Si-O membrane(on the microscope slide) and Mo-Fe-Si-O membrane (on the α-Al2O3 support) were obtained by diploid-circle-
dipping-coating. The effect of process conditions on the Fe-Si-O membrane and the influence of thermal treatment process on the Mo-Fe-Si-O membrane were studied
by DTA, XRD and SEM technique. The results indicated that the major factors affecting the Fe-Si-O membrane were sol viscosity, substrates,
dipping-coating time, withdrawal speed etc, and Mo-Fe-Si-O/α-Al2O3 membrane obtained by sol-gel method must be sintered at above 650℃
to form perfectly cubic phase structure. The membrane surfaces were crack-free after five times sintering at 700℃-cooling at 25℃
procedures.

Key words: sol-gel, Fe-Si-O sol, Mo-O sol, Mo-Fe-Si-O membrane

中图分类号: