高级检索
无机材料学报

无机材料学报 >

2009 , Vol. 24 >Issue 2: 301 - 304

DOI: https://doi.org/10.3724/SP.J.1077.2009.00301

研究论文

磨削表面损伤对RBSiC弯曲强度的影响

  • 姚 旺 ,
  • 张宇民 ,
  • 韩杰才 ,
  • 查炎峰 ,
  • 周玉锋 ,
  • 韩媛媛 ,
  • 曲 伟
展开
  • 哈尔滨工业大学 复合材料研究所， 哈尔滨 150001

收稿日期: 2008-05-13

  修回日期: 2008-07-28

  网络出版日期: 2009-03-20

收起

Effect of Grinding Induced Damage on Bending Strength of RBSiC

  • YAO Wang ,
  • ZHANG Yu-Min ,
  • HAN Jie-Cai ,
  • ZHA Yan-Feng，ZHOU Yu-Feng ,
  • HAN Yuan-Yuan ,
  • QU Wei
Expand
  • Center for Composite Materials, Harbin Institute of Technology, Harbin 150001, China

Received date: 2008-05-13

  Revised date: 2008-07-28

  Online published: 2009-03-20

Fold

摘要

借助X射线衍射方法测量了反应烧结碳化硅(RBSiC)材料的磨削表面的残余应力状态，并根据断裂力学评价了磨削引入的裂纹尺寸，分析了RBSiC的弯曲强度受磨削引入裂纹和残余应力的影响.研究表明，由于磨削过程中与磨削方向有关的机械载荷占主导作用，使磨削后的表面残余应力具有方向依赖性.砂轮轴向进给从0.90μm/s增加到1.35μm/s，磨削表面的残余压应力数值降低，计算得到的磨削引入的裂纹尺寸增大，导致强度下降.

关键词： 碳化硅; 磨削; 残余应力; 裂纹; 强度

本文引用格式

姚 旺 , 张宇民 , 韩杰才 , 查炎峰 , 周玉锋 , 韩媛媛 , 曲 伟 . 磨削表面损伤对RBSiC弯曲强度的影响[J]. 无机材料学报, 2009 , 24(2) : 301 -304 . DOI: 10.3724/SP.J.1077.2009.00301

Abstract

The effect of surface residual stress and crack on bending strength of reaction bonded silicon carbide (RBSiC) after grinding was investigated. The residual stress of the ground surfaces were determined using X-ray diffraction.The sizes of strength controlling cracks were assessed using fracture mechanics approach. The investigations show that mechanical load, which has relation with grinding direction, phays a dominateve role in the grinding processes. and the measured residual stresses have a direction dependency. With increase of down feed from 0.9μm/s to 1.35μm/s, the bending strength is reasonably correlated with the surface residual stress and crack size.

Key words： Silicon carbide; grinding; residual stress; crack; strength

参考文献

［1］黄清伟, 高积强, 金志浩. 西安交通大学学报, 2000, 34(2): 89-90.
［2］Robichaud J, Guregian J, Schwalm M. SiC optics for Earth observing applications. Earth Observing Systems VIII. Proc. SPIE 5151, 2003: 53-62.
［3］Tobin E, Magida M, Kishner S. Design, fabrication, and test of a meterclass reactionbonded SiC mirror blank. Silicon carbide materials for optics and precision structures. Proc. SPIE 2543, 1995: 12-21.
［4］Gopal A V, Rao P V. International Journal of Machine Tools and Manufacture, 2003, 43(13): 1327-1336.
［5］Zhang Y M, Zhang J H, Han J C, et al. Materials Letters, 2004, 58(7): 1204-1208.
［6］Bandyopadhyay B P, Ohmori H. International Journal of Machine Tools & Manufacture, 1999, 39(5): 839-853.
［7］朱洪涛, 林 滨, 吴 辉, 等. 精密制造与自动化，2004,2: 15-18.
［8］王西彬, 李相真.金刚石与磨料磨具工程, 1997, 6(102): 18-23.
［9］Eigenmann B, Macherauch E. Nuclear Instruments and Methods in Physics Research B, 1995, 97(1): 92-97.
［10］Immelmann S, Welle E, Reimers W. Material Science and Engineering A, 1997, 238(2):287-292.
［11］Genzel C, Klaus M, Denks I. Material Science and Engineering A, 2005, 390(1): 376-384.
［12］Yang H T, Gao L, Yuan R Z, et al. Materials Chemistry and Physics, 2003, 80(1): 305-308.
［13］李伯民，赵 波. 实用磨削技术. 北京: 机械工业出版社, 1996： 42-49.
［14］Tomba A G, Cavalieri A L. Materials Research Bulletin, 2000, 35(7): 1077-1085.
［15］Roberts S G, Lawrence C W, Bisrat Y. J. Am. Ceram. Soc., 1999, 82(7):1809-1816.
［16］Li K, Liao T W. Journal of Materials Processing Technology, 1996, 57(3): 207-220.
Options
文章导航

/

〈 〉