高压下纳米La0.8Sr0.2MnO3块状材料的成型及性能研究
收稿日期: 2009-10-21
修回日期: 2009-12-10
网络出版日期: 2010-05-12
Study on Molding and Performance for Nanometer La0.8Sr0.2MnO3 Massive Material under High
Received date: 2009-10-21
Revised date: 2009-12-10
Online published: 2010-05-12
在高压条件下制备出了晶粒尺寸为30nm左右的La0.8Sr0.2MnO3块状材料. 采用X 射线衍射仪(XRD)和场发射扫描电子显微镜(FESEM)对高压样品的相组成、晶粒尺寸及微观形貌进行了表征; 利用显微拉曼光谱仪测量了不同压力下制备出的块状样品在激光功率为400mW时位于100~3000cm-1之内的拉曼光谱. 结果表明, 高压烧结时样品的晶粒演化受温度和压力的共同影响:300℃以下时, 1~3GPa烧结的样品晶粒生长速度随压力的升高而增大, 4~5GPa烧结的样品其晶粒生长速度随压力的升高而减小; 300℃以上时, 其晶粒生长速度随压力和温度的升高而不断增大. 测量了高压烧结后纳米La0.8Sr0.2MnO3块状材料的各种物理性能, 结果表明, 高压烧结后该材料的显微硬度显著提高; 当烧结温度为300℃时, 不同压力下制得的样品的电阻率随压力的升高呈先减小后增大的趋势; 5GPa, 300℃时制出的样品在室温下呈典型的铁磁性能.
关键词: 高压; La0.8Sr0.2MnO3纳米材料; 性能
黄 浩1 , 邵光杰2 , 胡 婕1 , 2 . 高压下纳米La0.8Sr0.2MnO3块状材料的成型及性能研究[J]. 无机材料学报, 2010 , 25(5) : 473 -479 . DOI: 10.3724/SP.J.1077.2010.00473
The La0.8Sr0.2MnO3 massive samples were prepared with crystal grain size about 30nm under high pressure . The structure, grain size and morphology of the samples were characterized by Xray diffraction (XRD) and field emission scanning electron microscope(FESEM). Raman spectra of the samples was carried out by microRaman spectrometer in the range of 100-3000cm-1 with the laser power of 400mW. The results showed that the grain evolution of La0.8Sr0.2MnO3 was influenced by temperature and pressure. When the agglomeration temperature was below 300℃, the grain growth rate increased with increasing pressure at the sintering pressure of 1-3GPa while it fell down as pressure rised continuously at the sintering pressure of 4-5GPa. The grain growth rate increased with increment of pressure when the agglomeration temperature was over 300℃. Physical properties of agglomeration samples synthesized under high pressure were studied. Experimental results indicated that the microhardness of samples increased obviously after high pressure agglomeration. When sintering temperature was 300℃, the resistivity of samples decreased firstly then increased with increment of pressure. The sample prepared under 5GPa at 300℃ had obviously ferromagnetic character at room temperature.
Key words: high pressure; La0.8Sr0.2MnO3 nano-material; performance
[1]Mohan C R K, Bajpai P K. Effect of sintering optimization on the electrical properties of bulk BaxSr1-xTiO3 ceramics. Physica B, 2008, 403(13-16): 2173-2188.
[2]张 莉, 龚自正, 费英伟. 大块钙钛矿MgSiO3和镁方铁矿(Mg, Fe)O的高压合成. 高压物理学报, 2006, 20(4): 391-396.
[3]胡 婕, 邵光杰, 邢广忠(HU Jie, et al). Sr掺杂对钙钛矿型氧化物LaMnO3电催化性能的影响研究. 中国稀土学报(J. Rare Earth), 2008, 26(3): 351-356.
[4]巫 翔, 秦 善, 吴自玉, 等(WU Xiang, et al). 钙钛矿CaTiO3的超高压结构研究. 物理学报(Acta Physica Sinica), 2004, 53(6): 1967-1971.
[5]Marzi G D, Trodahl H J. The effect of Cu substitution on the A1g mode of La0.7Sr0.3MnO3 manganites. Solid State Communications,2003, 127(4):259-264
[6]Loridant S, Lucazeau G, Le Bihan T. A high pressure Raman and X-ray diffraction study of the perovskite SrCeO3.Journal of Physics and Chemistry of Solids,2002, 63(11):1983-1992
[7]秦秀娟, 邵光杰, 刘日平, 等(QIN Xiu-Juan, et al). 高性能ZnO纳米块体材料的制备及其拉曼光谱学特征. 物理学报(Acta Physica Sinica), 2006, 55(7): 3760-3764.
[8]袁小五, 朱建国, 肖定全, 等(YUAN Xiao-Wu, et al). (Pb0.9-xLa0.1Cax)TiO3纳米微粉的拉曼谱分析. 无机材料学报(Journal of Inorganic Materials), 2003, 18(3): 585-589.
[9]Zhernakov V S, Latysh V V, Zharikov A I, et al. The developing of nanostructured SPD Ti for structural use.Scripta Mater,2001, 44(879):1771-1774
[10]张江山, 鄂 蓓, 禹日成, 等. 高压下纳米尺寸Sr2FeMoO6粉末的结构稳定性和电学特性的研究.高压物理学报,2004, 18(3):193-196
[11]谈国太, 陈正豪, 章晓中(TAN Guo-Tai, et al). 钙钛矿锰氧化物La(1-x)TexMnO3(x=0.04,0.1)的两类磁电阻现象. 物理学报(Acta Physica Sinica), 2005, 1(54): 379-383.
[12]Valiev R Z, Islamgaliev R K, Alexandrov I V. Bulk nanostrucrured materials from severe plastic deformation.Progress in Materials Science,2000, 45(2):103-189
/
〈 |
|
〉 |