研究论文

脉冲激光沉积b轴取向BaTi2O5薄膜的研究

  • 王传彬 ,
  • 涂溶 ,
  • 後藤孝 ,
  • 沈强 ,
  • 张联盟
展开
  • 1. 武汉理工大学材料复合新技术国家重点实验室, 武汉 430070;
    2. 日本东北大学金属材料研究所, 仙台 980-8577

收稿日期: 2007-07-17

  修回日期: 2007-09-10

  网络出版日期: 2008-05-20

Preparation of b-axis Oriented BaTi2O5 Thin Films by Pulsed Laser Deposition

  • WANG Chuan-Bin ,
  • TU Rong ,
  • GOTO Takashi ,
  • SHEN Qiang ,
  • ZHANG Lian-Meng
Expand
  • 1. State Key Laboratory of Advanced Technology for Materials Synthesis and Processing,Wuhan University of Technology, Wuhan, 430070, China;
    2. Institute for Materials Research, Tohoku University, Sendai 980-8577, Japan

Received date: 2007-07-17

  Revised date: 2007-09-10

  Online published: 2008-05-20

摘要

采用脉冲激光沉积(PLD)技术, 在MgO(100)基片上制备了b轴取向的BaTi2O5薄膜, 研究了基片温度(Tsub)、氧分压(PO2)等沉积工艺对薄膜结构的影响. 结果表明: BaTi2O5薄膜的物相及取向性都随基片温度和氧分压的改变而变化, 薄膜呈现(710)或(020)取向生长, 最佳的PLD沉积条件为T sub=700℃和P O2=12.5Pa. 在该条件下, BaTi2O5薄膜表现出明显的b轴取向, 薄膜表面平整光滑, 结晶良好, 晶粒呈棒状交叉分布, 结合紧密.

本文引用格式

王传彬 , 涂溶 , 後藤孝 , 沈强 , 张联盟 . 脉冲激光沉积b轴取向BaTi2O5薄膜的研究[J]. 无机材料学报, 2008 , 23(3) : 553 -556 . DOI: 10.3724/SP.J.1077.2008.00553

Abstract

A new kind of b-axis oriented BaTi2O5 thin film was prepared on MgO (100) substrates by pulsed laser deposition. The effects of substrate temperature (T sub) and oxygen partial pressure (P O2) on the crystal phase and preferred orientation were investigated. The BaTi2O5 thin films exhibits (710) or (020) orientation, which depends on the substrate temperature and oxygen partial pressure. On the deposition condition of T sub=700℃ and P O2=12.5Pa, the b-axis oriented BaTi2O5 film is successfully obtained. The film has a dense and smooth surface, showing an elongated granular texture.

参考文献

[1] Scott J F, Dearaujo C. Science, 1989, 246 (4936): 1400--1405.
[2] Sayer M, Sreenivas K. Science, 1990, 247 (4946): 1056--1060.
[3] Evans J T. IEEE Journal Solid State Circuits, 1988, 23 (5): 117l--1185.
[4] Lee J Y, Lee B S. Materials Science and Engineering B, 2001, 79 (1): 86--89.
[5] OBryan H M, Thomson J. J. Am. Ceram. Soc., 1974, 57 (12): 522--526.
[6] Negas T, Roth R S, Parker H S, et al. J. Solid State Chem., 1974, 9 (3): 297--307.
[7] Ritter J J, Roth R S, Blendell J E. J. Am. Ceram. Soc., 1986, 69 (2): 155--162.
[8] Tangjuank S, Tunkasiri T. Appl. Phys. A, 2005, 81 (8): 1105--1107.
[9] Xu Y, Huang G, Long H. Materials Letters, 2003, 57 (22--23): 3570--3573.
[10] Wang L, Li G, Zhang Z. Materials Research Bulletin, 2006, 41 (4): 842--846.
[11] Akishige Y, Fukano K, Shigematsu H. Journal of Electroceramics, 2004, 13 (1--3): 561--565.
[12] Akashi T, Iwata H, Goto T. Mater. Trans., 2003, 44 (8): 1644--1646.
[13] Akashi T, Iwata H, Goto T. Mater. Trans., 2003, 44 (4): 802--804.
[14] Ashfold M N, Claeyssens F, Fuge G M, et al. Chem. Soc. Rev., 2004, 33 (1): 23--31.
[15] Tu R, Goto T. Materials Transactions, 2006, 47 (12): 2898--2903.
[16] Zhang J, Cui D F, Zhou Y L, et al. Thin Solid Films, 1996, 287 (1--2): 101--103.
[17] Zhu X H, Chan H L, Choy C L, et al. Appl. Phys. A, 2005, 80 (3): 591--595.
[18] Kimura T, Goto T, Yamane H, et al. Acta Cryst. C, 2003, 59 (12): i128--i130.
[19] Wahl G, Metz C, Samoilenkov S. J. Phys. IV France, 2001, 11 (Pr3): 835--846.
[20] Tu R, Kimura T, Goto T. Surface and Coating Technology, 2004, 187 (2--3): 238--244.
[21] Rossel M, Hoche H R, Leipner H S, et al. Anal. Bioanal. Chem., 2004, 380 (1): 157--162.
[22] Hushur A, Kojima S. Journal of the Korean Physical Society, 2005, 46 (1): 86--89.
文章导航

/