无机材料学报

• 研究论文 • 上一篇    下一篇

SiC表面氧化及其对SiC/Fe界面稳定性的影响

汤文明1,2; 郑治祥2; 丁厚福2; 金志浩1   

  1. 1. 西安交通大学金属材料强度国家重点实验室, 西安 710049; 2. 合肥工业大学材料科学与工程学院, 合肥 230009
  • 收稿日期:2000-03-13 修回日期:2000-05-08 出版日期:2001-03-20 网络出版日期:2001-03-20

Oxidation of SiC and Its Effect on the Interface Stability of SiC/Fe

TANG Wen-Ming1, 2; ZHENG Zhi-Xiang2; DING Hou-Fu2; JIN Zhi-Hao1   

  1. 1. State Key Laboratory for Mechanical Behavior of Materials; Xi an Jiaotong University; Xi an 710049; China; 2.Department of Materials Science and Engineering; Hefei University of Technology, Hefei 230009, China
  • Received:2000-03-13 Revised:2000-05-08 Published:2001-03-20 Online:2001-03-20

摘要: 烧结致密的α-SiC在静态空气气氛中经1200℃×10h氧化,在其表面形成一层致密的氧化膜,该层氧化膜具有β-方石英晶体结构.氧化膜的生长由O通过SiO晶格间隙的扩散控制. SiC/Fe界面反应剧烈,界面稳定性极差. SiC表面氧化能有效阻挡该界面反应,提高其稳定性. 900℃以下长时间保温,氧化 SiC/Fe界面十分平直,无明显反应的迹象,界面十分稳定.但随着温度的升高,界面稳定性越来越低,在局部区域内开始发生反应,并逐渐扩展到整个界面,最终导致氧化膜遭到破坏,失去阻挡界面反应的作用.氧化膜与SiC、Fe热膨胀系数不匹配所造成的应力集中,以及氧化膜中存在的孔隙可能是导致氧化膜在热处理过程中遭到破坏的主要原因.

关键词: 烧结SiC, 被动氧化, 界面稳定性, 反应阻挡层

Abstract: The dense oxide layer is formed on the surface of sintered α-SiC after annealing at 1200℃ for 10h in a stationary air ambient, and its crystal
structure is of β-cristobalite. The growth of the oxide layer is controlled by the diffusion of oxygen molecules through the interstitial site in SiO2. The solid state reaction between SiC and Fe is
severe, and significantly decreases the interface stability of SiC/Fe. The oxidation of SiC has a great effect on the interface stability of SiC/Fe. At temperatures below 900℃,
the interface of oxidized SiC/Fe is always smooth and remains intact after annealing for a long time. It shows that the oxide layer can hold back the interface reaction and
improve the interface stability, permanently. But, the interface stability of O-SiC/Fe decreases corresponding to raising the annealing temperature. The reaction first takes
place at the “points” of the interface, and then, wholly extends along the interface. It results that the effect of the oxide layer as a reaction barrier is lost entirely. The main
reasons for the oxide layer invalid after annealing at the temperature above 900℃ may be the voids existed in the oxide layer, and the stress concentration caused by the
mismatch of the heat expansion coefficients between the oxide layer and SiC, Fe.

Key words: sintered SiC, passive oxidation, interface stability, reaction barrier

中图分类号: